DEPT OF JUSTICE, FED PRISON INDUSTRIES, 320 1ST STREET NW -- Material Mgt Branch, WASHINGTON, DC 20534-0001

53 -- PARACENTRIC DEAD BOLT LOCK AND ACCESSORIES SOL 1PI-R-0689-97 1 DUE 021297 POC Contract Specialist, STONEBERGER, LOUISE, 202-305-7322 CORRECTION: This action was originally publicized in the CBD on January 24, 1997 and Amendment 0001 approximately February 9, 1997 and is hereby corrected to read as follows: Product is Paracentric Dead Bolt Lock and Accessories for delivery to UNICOR FCI Pekin, ILL. Bid closing date and time is changed to read February 18, 1997 at 2:00 p.m.. This is Amendment No. 0002 to Synopsis/Solicitation RFP 1PI-R-0689-97. Type of contract is changed to read "Firm-Fixed Price Requirement Type contract with Two (2) Option Years, if exercised". Quantities as stated are the estimated one year usage. Additional general item description is hereby furnished as follows: (1) KNOWN ACCEPTABLE DETENTION HARDWARE MANUFACTURERS: The firms listed below have been considered as acceptable manufacturers of detention hardware for previous FBOP projects and, provided that their products meet or exceed the requirements of this specification, may be considered acceptable for work of this Project. (1) Adtec Security, Inc. (2) Folger Adam Company (3) Southern Steel Company (4) Willo Products, Inc. (5) R.R. Brinks -- for 3020 locks only (6) Best Locks (7) NT Falcon Locks. (2) EMBEDDED ITEMS -- Embedded items shall be mild steel shapes and plate and, where required, shall be 5 mm or 6 mm, and shall comply with ASTM A366. (3) DETENTION HARDWARE -- (A) Furnish detention hardware, conduit system, wiring, and accessories for a complete security system to function properly as specified. Furnish templates of hardware if required by other contractors. Security hardware and accessories shall be furnished. Break-off-type fasteners shall be used for installation of all prison locks using the prison paracentric key, and for installation of the cover plates associated with these locks. Pinned Torx head screws shall be used at all other hardware installations. (B) SYSTEM DESCRIPTION: (C) MECHANICAL DEADLOCKS -- Similar to Folger Adam #12-6 and #16-6 (a) The lock case shall be made of drop-forged steel. The lock size shall be 4 1/2" x 3" x 1 1/4". The bolt size shall be not less than 1 1/2" x 3/4" milled from a high-strength bronze or hardened steel. Slide to be integral with bolt. The throw bolt shall be not less than 5/8 and shall be made of proper length to come flush with door frame when retracted. (b) The locks shall be keyed one side or two sides and shall have six (6) spring-tempered hard brass tumblers with notched ends. Each tumbler shall be activated by flat phosphor bronze spring. (c) The lock cylinder shall be made of polished alloy bronze having both hardness and tensile strength equal to mild steel. The cylinder shall extend 12.5mm beyond case and shall be grooved to match and guide similar grooves in key. (4) DEADLOCK similar to Folger Adam *32-6/#86-6: (a) The lock case shall be made of drop-forged steel. The bolt size shall be not less than 5 1/2" x 3 3/4" x 1 1/2". The bolt size shall be not less than 2" x 3/4" milled from a solid cold-finished steel bar. Slide to be integral with bolt. Each bolt to have three (3) hardened tool steel inserts not less than 6mm diameter, inserted into blind holes from the inside of lock. Inserts shall fill holes loosely so that they will turn against action of saws. The throw bolt shall be not less than 19mm and shall be made of proper length to come flush with door frame when retracted. (b) The lock shall be keyed one side or two sides and shall have six (6) spring-tempered hard brass tumblers with notched ends. Each tumbler shall be activated by flat phosphor bronze spring. (c) The lock cylinder shall be made of polished alloy bronze having both hardness and tensile strength equal to mild steel. The cylinder shall extend 12.5mm beyond case and shall be grooved to match and guide similar grooves in key. (d) These locks must first pass the following pressure test (which is required by the Federal Bureau of Prisons before and after installation): This test (using a torque wrench and a 19mm crow's foot) consists of applying 1.2 joules of pressure to the lock bolt in the locked position. Pressure shouldbe applied to the center of the lock bolt and then to the top and bottom of the lock bolt. If any lock fails the test, that lock shall be replaced with a lock that does meet the required test at no cost to the Government. (5) LOCK MOUNT SIMILAR TO FOLGER ADAM #HM: Prison locks on all hollow metal doors shall be mounted with Floger Adam lock mounting HM or equal. The lock shall be attached to the mounting plate with four (4) flat head spanner screws. The protruding ends of the screws shall be ground smooth and flush with the surface of the plate, which shall be made of 3/16" x 7" x 10" hot-rolled, pickled, and oiled steel, and shall be attached to door by eight (8) 1/4 -20x 1/2" flat twist-off head security screws. Edges of plat shall be neatly and uniformly beveled. Provide a Folger Adam #1 escutcheon. The pocket for the lock and the framing for attaching the NO. HM mounting shall be provided by the door manufacturer. The mounting plate shall fit on sunface with the face sheet of the door. Framing shall be 3mm thick steel channel, formed or rolled. (D) Manual-operated prison security lock, keyed one side, inmate's side blank (80 Series, Model 82-6). (E) Manual-operated Prison Security Lock Keyed one side (10 Series, Model 12-6). (F) CONTROL -- (A) Delivery of Keys: Manufacturer shall tag keys according to their corresponding locks and delivery directly to the Contracting Officer or his authorized representative and obtain signed receipt for same. Keyways assigned to this project shall be proprietary for use only by the FBOP and as approved by the Federal Bureau of Prisons' Supervisory Security Specialist. Delivery orders will include keying instructions, quanity and FBOP Security Office that will receive all locks and keys. Freight will be FOB origin. All (0041)

Loren Data Corp. http://www.ld.com (SYN# 0259 19970212\53-0010.SOL)