Fleet and Industrial Supply Center, Puget Sound, Bldg 467 W Street, Code 200 Bid Desk, Bremerton, WA 98314-0051

J -- REFURBISH FURNACE SOL 98082-9716 DUE 042098 POC E. Lee Gudgell (360)476-7082 WEB: Includes useful links to other acquisition sites and references., http://www.puget.fisc.navy.mil. E-MAIL: Contracting Officer, Lee Gudgell, lee_gudgell@ouget.fisc.navy.mil. To refurbish a Government-Owned Linberg Furnace, Model 11-MT-408040-G24, at Puget Sound Naval Shipyard, Building 59, Bremerton, WA. The contractor shall provide new fibre modules (or equal) to reline inside of furnace on-site at Puget Sound Naval Shipyard, Bldg 59, Bremerton, WA. The furnace, including its indivdual components, shall comply with the National Fire Protection Agency (NFPA) 70 and 79, and conform to the following: inside word camber, 111" deep x 60" wide x 54" high. The equipment specified herein shall be refurbished and/or modified to render it in full compliance with the applicable OSHA regulations and be listed by one of the OSHA-accredited laboratories or approved in accordance with Code of Federal Regulations (CFR) Title 29, Chapter XVII, Part 1910 and installed in accordance with applicable NEC/NFPA requirements. Approval shall be as specified under the "Approval" and "Acceptance" criteria in the OSHA regulations Subpart "O", Machinery and Machine Guarding, para 1010.212 and Subpart"S", Electrical, para 1910.303 and 1910.399. All machine parts, components, mechanisms, and assemblies furnished on the unit shall comply with all specific requirements of OSHA Safety and Health Standard (29 CFR 1910), General Industry, that are applicable to the equipment itself. Covers, platforms, guard rails, belt guards, and other safety devices shall be provided for all parts of the equipment that present a safety hazard. Safety devices shall prevent unintentional contact with the guarded part, but shall not interfere with the operation of the equipment. Safety devices shall be removable to facilitate inspection, maintenance, and repair of the part. The Contractor shall be responsible for providing and performing the following: RELINING OF FURNACE- provide ITC fibre modules for entire furnace area, provide technical assistance during installation of fibre modules, and provide all necessary miscellaneous repair material for relining. TECHNICAL ASSISTANCE TO BE INCLUDED- during installation, first firing of furnace to ensure proper heating. The Government shall be responsible for providing and performing the following: to relocate single gas burner from right side to front left side to be alongside the two burners which are already in the system; to remove exhaust system on left side and provide one only on the right side for correct balance of exhaust in the furnace system; to remove old insulation inside furnace; and to install fibre modules (or equal) to inside of furnace. Note(s): 1 and 26 apply. To be procured under Simplified Acquisition Procedures. RYG Program is applicable to the requirement. The Government does not hold any of the specifications or drawings. This notice constitutes a complete Request for Quotation (RFQ). No additional RFQ is available. Quotes may be mailed to FISC Puget Sound, Code 204.30, 467 W Street, Bremerton, WA 98314-5100, or emailed to lee_gudgell@puget.fisc.navy.mil or fax to (360) 476-3316. Solicitation number must be cited in either case. The quote must contain a certification that the offeror is a large, small, small-disadvantaged, or small woman-owned business; be FOB destination; include proposed delivery schedule and discount/payment terms; warranty duration (if applicable); and be signed by an authorized company representative. Offeror should include Taxpayer Identification Number (TIN), DUN & Bradstreet Number (DUNS), CAGE Code and Remit To address. All responsible sources may submit offer/bid which shall be considered by FISC Puget Sound. QUOTES ARE DUE BY 4:00 P.M. PACIFIC STANDARD TIME, RESPONSE DATE LISTED ABOVE. (0092)

Loren Data Corp. http://www.ld.com (SYN# 0046 19980407\J-0003.SOL)