|
COMMERCE BUSINESS DAILY ISSUE OF JUNE 30,1998 PSA#2127NASA/Goddard Space Flight Center, Code 212, Greenbelt, MD 20771 34 -- METAL LATHE & ACCESSORIES SOL RFQ5-76940-946 DUE 070698 POC
Agnes Smith, Purchasing Agent, Phone (301)286-5466, Fax (301)286-0247,
Email Agnes.L.Smith.1@gsfc.nasa.gov -- Leigh Anne C. Giraldi,
Contracting Officer, Phone (301)286-7464, Fax (301)286-0247, Email
Leigh.Anne.C.Giraldi.1@gsfc.nasa.gov WEB: Click here for the latest
information about this notice,
http://nais.nasa.gov/EPS/GSFC/date.html#RFQ5-76940-946. E-MAIL: Agnes
Smith, Agnes.L.Smith.1@gsfc.nasa.gov. The purpose of this modification
is to extend the proposal response date to July 6, 1998. This notice
is a combined synopsis/solicitation for commercial items prepared in
accordance with the format in FAR Subpart 12.6, as supplemented with
additional information included in this notice. This announcement
constitutes the only solicitation; quotes are being requested and a
written solicitation will not be issued. This procurement is being
conducted under the Simplified Acquisition Procedures (SAP). Item 1 --
Metal Lathe, 14" swing over bed 14", swing in gap 20", distance
between centers 40", bed width 10", hole thru spind le 1-5/8", tail
stock spindle dia. 1-7/8", center 4mt, spindle travel 4-3/8", motor
3hp, 1800 rpm, 460 volt, controls: magnetic starter, 110v to controls,
18 speeds various- quantity 1 EACH Item 2 -- Face plates -- quantity
1 EACH Item 3 -- Follower rest -- quantity 1 EACH Item 4 -- Rear Tool
Post -- quantity 1 EACH Item 5 -- Quick Change Tool Post -- quantity1
EACH Item 6 -- Live Center -- quantity 1 EACH Item 7 -- Hand Wheel
Collect Chuck -- quantity 1 EACH Item 8 -- Lower Collet Chuck --
quantity 1 EACH Item 9 -- Taper Attachments -- quantity 1 EACH Item 10
-- Micro Carriage Stoop -- quantity 1 EACH Item 11 -- Roller Fingers
-- quantity 1 EACH The provisions and clauses in the RFQ are those in
effect through FAC 97-04. This procurement is a total small business
set-aside. See Note 1. The SIC code and the small business size
standard for this procurement are 3416 and 500, respectively. The
quoter shall state in their quotation their size status for this
procurement. All qualified responsible business sources may submit a
quotation which shall be considered by the agency. Quotations for the
items(s) described above may be mailed or faxed to the identified point
of contact., taxpayer identification number (TIN), identification of
any special commercial terms, and be signed by an authorized company
representative. Quoters are encouraged to use the Standard Form 1449,
Solicitation/Contract/Order for Commercial Items form found at URL:
http://procure.arc.nasa.gov/Acq/Standard_Forms/Index.html to submit a
quotation. Quoters shall provide the information required by FAR
52.212-1. If the end product(s) quoted is other than domestic end
product(s) as defined in the clause entitled "Buy American Act --
Supplies," the quoter shall so state and shall list the country of
origin. The Representations and Certifications required by FAR 52.2l2-3
may be obtained via the internet at URL:
http://ec.msfc.nasa.gov/msfc/pub/reps_certs/sats/ FAR 52.212-4 is
applicable. Questions regarding this acquisition must be submitted in
writing no later than June 23, 1998. Quotations are due by 5:00pm EST,
June 26, 1998, to the address specified above. Selection and award
will be made to the lowest priced, technically acceptable quoter.
Technical acceptability will be determined by information submitted by
the quoter providing a description in sufficient detail to show that
the product quoted meets the Government's requirement. Quoters must
provide copies of the provision at 52.212-3, Offeror Representation and
Certifications -- Commercial Items with their quote. See above for
where to obtain copies of the form via the Internet. An ombudsman has
been appointed -- See Internet Note "B". Posted 06/26/98 (0177) Loren Data Corp. http://www.ld.com (SYN# 0255 19980630\34-0002.SOL)
34 - Metalworking Machinery Index Page
|
|