General Services Administration, Federal Supply Service (FSS), Tools and Appliances Commodity Center (6FE), 1500 East Bannister Road, Kansas City, MO, 64131

51 -- CBD FOR TOOL KIT, TUBE FITTING, SOL 6FES-E2-980209-N SOL 6FES-E2-980209-N DUE 091898 POC Steve Mosby, Contract Specialist, Phone (816) 823-1294, Fax (816) 926-3678, Email steve.mosby@gsa.gov -- Alan Basler, Contract Specialist, Phone (816) 823-1297, Fax (816) 926-3678, Email alan.basler@gsa.gov WEB: Visit this URL for the latest information about this, http://159.142.150.114/cgi-bin/WebObjects/EPS?ActionCode=P&;ProjectID=6 FES-E2-980209-N&LocationID=7. E-MAIL: Steve Mosby, steve.mosby@gsa.gov. 1. 5180-01-341-4030 TOOL KIT, TUBE FITTING:DESCRIPTION Kit contains tools needed to cut and deburr tubing and install all configurations of permaswage fittings in sizes 4, 6, 8, 10 and 12 on aircraft hydraulic line sizes 1/4 inch to 3/4 inch diameter. Compact size allows swaging of lines in confined areas with one hand operation. Kit shall contain instruction manual on the use of all tool components and in the proper performance of swaging tilizing permaswage fittings.. END ITEM IDENTIFICATION: DEUTSCH METAL COMPONENTS PART NUMBER DLTFRPSKT3001 OR EQUAL. Offering on:Manufacturer's Name: __________________________Brand___________________________________Model or Part No. __________________________________HEADER INFORMATION The following header paragraph(s) shall apply to the item purchase description(s) where applicable. If there is a conflict between the item purchase description and the header paragraph(s), the header paragraph(s) shall take precedence over the item purchase description. Notwithstanding the requirements specified herein, cadmium plating is not acceptable. In the event no alternative coating, finish, or plating is specified, a rust preventative finish as used in standard commercial practice shall apply. Each set or kit shall contain a dated parts list or packing list citing the GSA contract number (if applicable), GSA purchase order number, date of purchase order, kit national stock number (NSN), each component NSN (if applicable), kit noun name, each component noun name, and quantity of each component. Unless otherwise specified in the item purchase description, each kit or set and each component of the kit or set shall have, in addition to any other required marking, identification marking indicating the manufacturer's name or identifying symbol, and the state or country of manufacture. The marking shall be engraved, etched, or stamped in such a manner that it will be permanent to the extent that it will remain clear and legible throughout the life of the item. Workmanship: Details of workmanship shall be in accordance with the best commercial standards and practices. Paints, coatings, platings, and finishes shall be smooth, adherent, continuous, and not stained or discolored. Fasteners shall be firmly secured and show no evidence of deformation, cross threading, or hazardous burrs. Adhesives and lubricants adequate for their intended purpose shall be properly and neatly applied. Adhesives shall be adequately cured. Wires and cables shall be neatly dressed and shall not be frayed or in contact with sharp edges. Wire and cable insulation shall show no evidence of burns, abrading, or pinch marks. There shall be no interference, binding, or galling of parts. External and bearing surfaces shall be free of tool and gouge marks, nicks, or other surface imperfections. The item shall be clean and free of corrosion and debris (e.g. chips shavings, slivers) or other foreign material. The item shall be free from manufacturing workmanship defects (e.g., loose, missing, binding or misaligned parts, sharp or rough external edges, corners or surfaces) and material defects (e.g., pits, rips, fins, burrs, tears, nodules, cracks, blisters) which may adversely impact the item's serviceability, durability, safety, or appearance. TECHNICAL DATA PACKAGES All alternate offeror's technical data packages for evaluation shall include either sufficient dimensions and tolerances or a sample so as to be readily evaluated as to whether the alternate is equal to the original item of supply in form, fit, and function PACKAGING Packaging in accordance with standard commercial practice. PACKING Packing in accordance with standard commercial practice. MARKING Marking in accordance with current version of Fed. Std. 123.BIDDERS OFFERING OTHER THAN BRAND NAME ITEMS IDENTIFIED HEREIN MUST FURNISH WITH THEIR BIDS ADEQUATE DESCRIPTIVE LITERATURE SO THAT A DETERMINATION CAN BE MADE AS TO EQUALITY OF THE PRODUCTS OFFERED. IN ORDER FOR THE GOVERNMENT TO MAKE AN "OR EQUAL" DETERMINATION OF THE OFFERED PRODUCT(S), THE FURNISHED INFORMATION MUST DELINEATE EACH APPLICABLE CHARACTERISTIC, UNIT OF MEASURE, AND TEST METHOD OF THE OFFERED PRODUCT(S) DIRECTLY CORRELATED TO EACH OF THE REQUIREMENTS DELINEATED IN THE ITEM PURCHASE DESCRIPTION. FAILURE TO FURNISH THIS INFORMATION/LITERATURE WILL RESULT IN THE BID BEING REJECTED AS NON-RESPONSIVE OR MAY BE CONSIDERED AS UNACCEPTABLE FOR AWARD IN A NEGOTIATED PROCUREMENT (SEE GSAR CLAUSE 552.211-70). Posted 09/02/98 (D-SN244854). (0245)

Loren Data Corp. http://www.ld.com (SYN# 0204 19980904\51-0003.SOL)