NASA/George C. Marshall Space Flight Center, Procurement Office, Marshall Space Flight Center, AL 35812

66 -- PRESSURE TRANSDUCERS SOL 8-1-8-02-C1412 POC Kimberly R. Day, Contract Specialist, Phone (256) 544-8999, Fax (256) 544-4080, Email kimberly.day@msfc.nasa.gov -- Teresa A. Foley, Contracting Officer, Phone (256) 544-0335, Fax (256) 544-4080, Email teresa.foley@msfc.nasa.gov WEB: Click here for the latest information about this notice, http://nais.nasa.gov/EPS/MSFC/date.html#8-1-8-02-C1412. E-MAIL: Kimberly R. Day, kimberly.day@msfc.nasa.gov. This notice is a combined synopsis/solicitation for commercial items prepared in accordance with the format in FAR Subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; quotes are being requested and a written solicitation will not be issued. This procurement is being conducted under the Simplified Acquisition Procedures (SAP). Line Item No: 1 Quantity: 2 Unit: Ea Differential Pressure Transducer, 5 Psid Range, Unidirectional, Wet/Wet, Vendor Must Supply Mating Connector And Potting Boot To Form Environmental Seal At Electrical Connector, Psid Units, Internal 80% Cal Resistor, Stellar Technologies Part Number DT400-5UD-129, Or Equal Meeting Attached Specs. No Deviations. Must Be "Strain Gage" Tranducer, 1500 Psi Static Pressure Applied To High Or Low Side Must Create No Permanent Change In Zero Or Calibration, Mechanical Stop To Prevent Damage Due To Over Pressure. Line Item No: 2 Quantity: 2 Unit: Ea Pressure Transducer,Psia Units, 100 Psia Range, General Purpose Use, Replaceable Diaphragm With Mechanical Stop To Prevent Damage Due To Overpressure, Vendor Must Supply Mating Connector And Potting Boot To Form Environmental Seal At Electrical Connector, Stellar Part Number Gt200-100a-138 Or Equal Meeting the Attached "General Purpose Pressure Tranducer" Specs. No Deviations. Must Be A "Strain Gage" Transducer And Lox Compatible. Line Item No: 3 Quantity: 1 Unit: Ea Same As Item #1 Except 25 Psid Range, Stellar Part Number Dt400-25ud-129 Or Equal Which Meets Attached Specs. Line Item No: 4 Quantity: 2 Unit: Ea Pressure Transducer, Psia Units, 100 Psia Range, General Purpose Use, Replaceable Diaphragm With Mechanical Stop To Prevent Damage Due To Overpressure, Vendor Must Supply Mating Connector And Potting Boot To Form Environmental Seal At Electrical Connector, Stellar Part Number Gt200-100a-138 Or Equal Which Meets Attached "General Purpose Pressure Tranducer" Specs. No Deviations. Must Be A "Strain Gage" Transducer And Lox Compatible. Line Item No: 5 Quantity: 2 Unit: Ea Same As #4 Except Psia Units And 200 Psia Range, Stellar Part Number GT200-200A-138 Or Equal Which Meets Attached "General Purpose Transducer" Specs. Line Item No: 6 Quantity: 2 Unit: Ea Same As #4 Except Psia Units And 200 Psia Range, Stellar Part Number GT200-200A-138 Or Equal Which Meets Attached "General Purpose Transducer" Specs. Line Item No: 7 Quantity: 2 Unit: Ea Same As Item #4 Except Psia Units And 500 Psia Range, Stellar Part Number GT200-500A-138 Or Equal Which Meets Attached "General Purpose Transducer" Specs. Line Item No: 8 Quantity: 3 Unit: Ea Same As Item #4 Except Psia Units And 1000 Psia Range, Stellar Part Number GT200-1000A-138 Or Equal Which Meets Attached "General Purpose Transducer" Specs. Line Item No: 9 Quantity: 1 Unit: Ea Same As Item #4 Except Psig Units And 1000 Psig Range, Stellar Part Number GT200-1000G-138 Or Equal Which Meets Attached "General Purpose Transducer" Specs. Line Item No: 10 Quantity: 14 Unit: Ea Same As Item #11 Except Psig Units And 100 Psig Range, Stellar Part Number ST500-100G-162 Or Equal Which Meets Attached "Cryogenic Pressure Tranducer" Specs. Line Item No: 11 Quantity: 2 Unit: Ea Pressure Transducer, Cryogenic Use, Lox Compatible, Mechanical Stop To Prevent Damage Due To Overpressure, Compensated Temperature Range -320 To 70 Deg F, Operating Range -450 To 300 Deg F, Psia Units And 100 Psia Range, Stellar Part Number ST500-100A-162 Or Equal Which Meets Attached "Cryogenic Pressure Transducer" Specs. No Deviations. Must Be "Strain Gage" Transducer. Vendor Must Supply Mating Connector And Potting Boot To Form Environmental Seal At Electrical Connector. Line Item No: 12 Quantity: 1 Unit: Ea Same As Item #11 Except Psig Units And 100 Psig Range, Stellar Part Number ST500-100G-162 Or Equal Which Meets Attached "Cryogenic Pressure Tranducer" Specs. Line Item No: 13 Quantity: 2 Unit: Ea Same As Item #11 Except Psia Units And 200 Psia Range, Stellar Part Number ST500-200A-162 Or Equal Which Meets Attached "Cryogenic Pressure Transducer" Specs. Line Item No: 14 Quantity: 3 Unit: Ea Same As Item #11 Except Psia Units And 500 Psia Range, Stellar Part Number ST500-500A-162 Or Equal Which Meets Attached "Cryogenic Pressure Transducer" Specs. Line Item No: 15 Quantity: 1 Unit: Ea Same As Item #11 Except Psia Units And 1000 Psia Range, Stellar Part Number ST500-1000A-162 Or Equal Which Meets Attached "Cryogenic Pressure Transducer" Specs. Line Item No: 16 Quantity: 9 Unit: Ea Same As Item #11 Except Psia Units And 1500 Psia Range, Stellar Part Number ST500-1500A-162 Or Equal Which Meets Attached "Cryogenic Pressure Transcucer" Specs. Line Item No: 17 Quantity: 2 Unit: Ea Pressure Transducer, Mechanical Stop To Prevent Damage Due To Over Pressure, Lox Compatible, Vendor Must Supply Mating Connector And Potting Boot To Form Environmental Seal At Electrical Connector, High Temperature Use, Compensated Temperature Range 70 To 400 Deg F, Operating Temperature -100 To +425 Deg F, Psia Units And 100 Psia Range, Stellar Part Number ST500-100A-163 Or Equal Which Meets Attached "High Temperature Tranduscer Specs. No Deviation. Must Be "Strain Gage" Transducer. ***Connector -- Mil-C-38999/26FC98SN & Potting Boot To Be Supplied By Vendor At No Charge**** Line Item No: 18 Quantity: 2 Unit: Ea Same As Line Item #4 Except Psig Units With 200 Psig Range, Stellar Part Number Gt200-200g-138 Or Equal Which Meets Attached "General Purpose Transducer" Specs. The provisions and clauses in the RFQ are those in effect through FAC 97-06. This procurement is a total small business set-aside. The SIC code and the small business size standard for this procurement are 3679 and 500, respectively. The quoter shall state in their quotation their size status for this procurement. All qualified responsible business sources may submit a quotation which shall be considered by the agency. Delivery to MSFC is required within 30 days ARO. Delivery shall be FOB Destination. The DPAS rating for this procurement is DO-C9. Quotations for the items(s) described above maybe mailed or faxed to the identified point of contact by the date/time specified and include, solicitation number, FOB destination to this Center, proposed delivery schedule, discount/payment terms, warranty duration (if applicable), taxpayer identification number (TIN), identification of any special commercial terms, and be signed by an authorized company representative. Quoters are encouraged to use the Standard Form 1449, Solicitation/Contract/Order for Commercial Items form found at URL: http://procure.arc.nasa.gov/Acq/Forms/Index.html to submit a quotation. Quoters shall provide the information required by FAR 52.212-1 with the exception of (d), (h), and (i). If the end product(s) quoted is other than domestic end product(s) as defined in the clause entitled "Buy American Act -- Supplies," the quoter shall so state and shall list the country of origin. The Representations and Certifications required by FAR 52.2l2-3 may be obtained via the internet at URL: http://ec.msfc.nasa.gov/msfc/pub/reps_certs/sats/ FAR 52.212-4 is applicable. Addenda to FAR 52.212-4 are as follows: 52.204.4, 52.211-15, and 52.247-34. FAR 52.212-5 is applicable and the following identified clauses are incorporated by reference: FAR 52.212-5(b), 52.222-35, 52.222-36, 52.222-27, and 52.225-3. Questions regarding this acquisition must be submitted in writing no later than October 7, 1998. Quotations are due by October 9, 1998 to the address specified above and to the attention of Kimberly R. Day. Selection and award will be made (on an aggregate basis) to the lowest priced, technically acceptable quoter. Technical acceptability will be determined by information submitted by the quoter providing a description in sufficient detail to show that the product quoted meets the Government's requirement. Quoters must provide copies of the provision at 52.212-3, Offeror Representation and Certifications -- Commercial Items with their quote. See above for where to obtain copies of the form via the Internet. An ombudsman has been appointed—See Internet Note "B". It is the quoter's responsibility to monitor this site for the release of amendments (if any). Potential quoters will be responsible for downloading their own copy of this combination synopsis/solicitation and amendments (if any). Posted 10/01/98 (D-SN257335). (0274)

Loren Data Corp. http://www.ld.com (SYN# 0220 19981005\66-0003.SOL)