Department of Veterans Affairs, James A. Haley Veterans Hospital, AMMS (90C), 13000 Bruce B. Downs Blvd., Tampa, FL 33612

65 -- MAXILLO FACIAL, 3.0 CANNULATED SCREW SET & SMALL FRAGMENT INSTRUMENT SET SOL 796-99-03 DUE 031599 POC Elvis Soler 813-972-7504/Fax 813-903-4838 This is a combined synopsis for commercial items prepared in accordance with subparts in 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation and a written solicitation will not be issued. This solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 97-10. The James A. Haley VA Hospital intends to enter into a sole source purchase order with Synthes (USA), Paoli, PA, in accordance with subparts in 6.302-1ii, to replenish the sets that have been depleted. Synthes manufactures and sells their own products and does not sell to or distribute their product line to any other source or supplier. This source is requested because the surgeons have been trained on this system, are familiar with and prefer its use. A new system could take months of training to bring the entire OR staff up to competent levels to use. The Operating Room needs to have this system on hand, sterile, at all times for emergency and routine uses. Presently, this system is borrowed from downtown then replacements are re-ordered immediately which puts an unnecessary strain and burden on their supply. Also, despite the varied characteristics of each tool or implant, one feature remains constant, metal compatibility. Implants when inserted must not be mismatched. When this occurs, documented cases have proven mixing of metals increases the risk of patient reaction. In the case of adverse patient reaction, implants may require removal and a compatible implant reinserted. These duplicate surgeries are not only costly but can place the patient at considerable risk by subjecting them to subsequent trauma and stress. Currently, all of their operating implant systems are Synthes brand products. In conclusion, it would be not only be costly to the Government, but would not be in the best interest of the patient who we must consider above all else to consider any other source. The James A. Haley VA Hospital intends to purchase: A) Maxillofacial set: (1ea) 1.3mm module set with T1 implants to include; (1ea) 1.3mm module for T1 implants; (1ea) screw length marker kit for 1.3mm module; (2ea) 1.3mm screwdriver blade with holding sleeve; (2ea) 1.0mm drill bit/stryker j-ltch with 4mm stop/44.5mm; (2ea) 1.0mm drill bit/stryker j-ltch with 6mm stop/44.5mm; (2ea) 1.0mm drill bit/stryker j-ltch with 8mm stop/44.5mm; (10ea) 1.3mm T1 mf cortex screw self-tapping w/flutes 3mm; (10ea) 1.3mm T1 mf cortex screw self-tapping w/flutes 4mm; (10ea) 1.3mm T1 MF cortex screw self-tapping w/flutes 5mm: (10ea) 1.3mm T1 mf cortex screw self tapping w/flutes 6mm; (10ea) 1.3mm T1 mf cortex screw self-tapping w/flutes 8mm; (2ea) 1.7mm T1 emergency screw w/fluted tip 3mm; (2ea) 1.7mm T1 emergency screw w/fluted tip 4mm; (2ea) 1.7mm T1 emergency screw w/fluted tip 5mm; (2ea) 1.7mm T1 emergency screw w/fluted tip 6mm; (2ea) 1.7mm T1 emergency screw w/fluted tip 8mm; (3ea) 1.3mm T1 adaption plate 24 holes/95mm; (3ea) 1.3mm T1 orbital rim plate 9 holes; (3ea)1.3mm T1 oblique L-Plate 3 x 3 holes-left; (3ea)1.3mm T1 oblique L-Plate 3 x 3 holes-right; (3ea)1.3mm T1 oblique L-Plate 3 x 4 holes-left; (3ea)1.3mm T1 oblique L-Plate 3 x 4 holes-right; (3ea) 1.3mm T1 Y-plate 1 x 3 holes; (3ea) 1.3mm T1 Y-plate 3 x 4 holes; (1ea) 1.5mm module set with T1 implants to include: (1ea) 1.5mm module for T1 implants; (1ea) screw length marker kit for 1.5mm module; (2ea) 1.5mm/2.0mm screwdriver blade with holding sleeve, short; (2ea) 1.1mm drill bit/stryker j-ltch with 4mm stop/44.5mm; (2ea) 1.1mm drill bit/stryker j-ltch with 6mm stop/44.5mm; (2ea) 1.1mm drill bit/stryker j-ltch with 8mm stop/44.5mm; (2ea) 1.1mm drill bit/stryker j-ltch with 12mm stop/44.5mm; (10ea) 1.5mm T1 mf cortex screw self-tapping w/flutes 4mm; (10ea) 1.5mm T1 mf cortex screw self-tapping w/flutes 6mm; (10ea) 1.5mm T1 mf cortex screw self-tapping w/flutes 8mm; (4ea) 1.5mm T1 mf cortex screw self-tapping w/flutes 10mm; (4ea) 1.5mm T1 mf cortex screw self-tapping w/flutes 12mm; (2ea) 2.0mm T1 emergency screw w/fluted tip 4mm; (2ea) 2.0mm T1 emergency screw w/fluted tip 6mm; (2ea) 2.0mm T1 emergency screw w/fluted tip 8mm; (2ea) 2.0mm T1 emergency screw w/fluted tip 10mm; (2ea) 2.0mm T1 emergency screw w/fluted tip 12mm; (3ea) 1.5mm T1 adaption plate 20 holes/90mm; (3ea) 1.5mm T1 orbital rim plate 12 holes; (3ea) 1.5mm T1 oblique L-plate 2 x 3 holes -- left; (3ea) 1.5mm T1 oblique L-plate 2 x 3 holes -- right; (3ea) 1.5mm T1 oblique L-plate 3 x 4 holes -- left; (3ea) 1.5mm T1 oblique L-plate 3 x 4 holes -- right; (3ea) 1.5mm T1 Y-plate 1 x 3 holes; (3ea) 1.5mm T1 X-plate 4 holes (1ea) 2.0mm module set with T1 implants to include: (1ea) 2.0mm module for T1 implants; Screw length marker kit for 2.0mm module; (2ea) 1.5mm/2.0mm screwdriver blade with holding sleeve, long; (2ea) 1.5mm drill bit/stryker j-ltch with 4mm stop/44.5mm; (2ea) 1.5mm drill bit/stryker j-ltch with 6mm stop/44.5mm; (2ea) 1.5mm drill bit/stryker j-ltch with 8mm stop/44.5mm; (2ea) 1.5mm drill bit/stryker j-ltch with 12mm stop/44.5mm; (8ea) 2.0mm T1 mf cortex screw self-tapping w/flutes 4mm; (8ea) 2.0mm T1 mf cortex screw self-tapping w/flutes 6mm; (4ea) 2.0mm T1 mf cortex screw self-tapping w/flutes 8mm; (2ea) 2.0mm T1 mf cortex screw self-tapping w/flutes 10mm; (2ea) 2.0mm T1 mf cortex screw self-tapping w/flutes 12mm; (2ea) 2.0mm T1 mf cortex screw self-tapping w/flutes 14mm; (2ea) 2.0mm T1 mf cortex screw self-tapping w/flutes 16mm; (2ea) 2.0mm T1 mf cortex screw self-tapping w/flutes 18mm; (2ea) 2.4mm T1 emergency screw 6mm; (2ea) 2.4mm T1 emergency screw 8mm; (2ea) 2.4mm T1 emergency screw 10mm; (2ea) 2.4mm T1 emergency screw 12mm; (2ea) 2.4mm T1 emergency screw 14mm; (2ea) 2.4mm T1 emergency screw 16mm; (2ea) 2.4mm T1 emergency screw 18mm; (3ea) 2.0mm T1 Zygomatic plate 4 holes/22mm; ; (3ea) 2.0mm T1 Zygomatic plate 5 holes/27mm; ; (3ea) 2.0mm T1 Zygomatic plate 6 holes/32mm; ; (3ea) 2.0mm T1 Zygomatic plate 20 holes/100mm; (3ea) 2.0mm T1 orbital rim plate 12 holes; (3ea) 2.0mm T1 adaption plate w/30 broad spaced holes/193mm; (3ea) 2.0mm T1 obique L-plate 2 x 3 holes-left; (3ea) 2.0mm T1 obique L-plate 2 x 3 holes-right; ; (3ea) 2.0mm T1 obique L-plate 3 x 4 holes-left; ; (3ea) 2.0mm T1 obique L-plate3 x 4 holes-right; ; (3ea) 2.0mm T1 obique L-plate 4 x 6 holes-left; ; (3ea) 2.0mm T1 obique L-plate 4 x 6 holes-right; ; (3ea) 2.0mm T1 Y-plate 2 x 4 holes; ; (3ea) 2.0mm T1 X-plate 4 holes (1ea) 1.0mm module set with T1 implants to include: (1ea) 1.0mm module for T1 implants; Screw length marker kit for 1.0mm module; (2ea) 1.0mm screwdriver blade with holding sleeve (2ea) 0.70mm drill bit/stryker j-ltch with 3mm stop/44.5mm; (2ea) 0.76mm drill bit/stryker j-ltch with 5mm stop/44.5mm; (2ea) 0.76mm drill bit/stryker j-ltch with 8mm stop/44.5mm; (8ea) 1.0mm T1 mf cortex screw self-tapping w/flutes 2mm; (12ea) 1.0mm T1 mf cortex screw self-tapping w/flutes 3mm; (12ea) 1.0mm T1 mf cortex screw self-tapping w/flutes 4mm; (12ea) 1.0mm T1 mf cortex screw self-tapping w/flutes 5mm; (8ea) 1.0mm T1 mf cortex screw self-tapping w/flutes 6mm; (2ea) 1.2mm T1 emergency screw w/fluted tip 2mm; (2ea) 1.2mm T1 emergency screw w/fluted tip 3mm; (2ea) 1.2mm T1 emergency screw w/fluted tip 4mm; (2ea) 1.2mm T1 emergency screw w/fluted tip 5mm; (2ea) 1.2mm T1 emergency screw w/fluted tip 6mm; (3ea) 1.0mm T1 strut plate 16 holes; (3ea) 1.0mm T1 strut plate 22 holes; (3ea) 1.0mm T1 adaption plate 34 holes/100mm; (3ea) 1.0mm T1 orbital rim plate 11 holes; (3ea) 1.0mm T1 L-plate 4 x 5 holes-left; (3ea) 1.0mm T1 L-plate 4 x 5 holes-right; (3ea) 1.0mm T1 Y-plate 2 x 5 holes; (3ea) 1.0mm T1 Y-plate 3 x 7 holes; (3ea) 1.0mm T1 double Y-plate 1 x 2 holes; (3ea) 1.0mm T1 T-plate 5 x 5 holes; (3ea) 1.0mm T1 T-plate 5 x 7 holes; (3ea) 1.0mm T1 X-plate 5 holes; (3ea) 1.0mm T1 H-plate 6 holes; (3ea) 1.0mm T1 H-plate 11 holes (2ea) 2.0mm T1 mf cortex screw self-tapping w/flutes 4mm; (3ea) 2.0mm T1 mf cortex screw self-tapping w/flutes 6mm; (6ea) 2.0mm T1 mf cortex screw self-tapping w/flutes 8mm; (2ea) 1.0mm T1 mf cortex screw self-tapping w/flutes 4mm; (2ea) 1.0mm T1 mf cortex screw self-tapping w/flutes 5mm; (2ea) 1.0mm T1 mf cortex screw self-tapping w/flutes 6mm; (4ea) 1.3mm T1 mf cortex screw self-tapping w/flutes 6mm; (6ea) 1.3mm T1 mf cortex screw self-tapping w/flutes 8mm; (1ea) craniofacial modular fixation instrument set/4-module; (1ea) T2 cranialfacial modular fixation system graphic case; (2ea) handle w/mini quick coupling small; (1ea) combination bending pliers for 1.0mm/2.0mm plates; (1ea) plate holding forceps for 1.5mm, 2.0mm, & 2.4mm plates; (1ea) combination bending/cutting pliers for 1.0mm-2.0mm plates; (1ea) plate cutters for 1.0mm, 1.3mm, 1.5mm, 2.0mm plates; (1ea) plate holding forceps, locking for 1.5mm & 2.0mm plates A) 3.0mm Cannulated Screw set: (1ea) 3.0mm cannulated screw instrument & implant set to include: (3ea) cannulated screw short thread/14mm; : (3ea) cannulated screw short thread/15mm; : (3ea) cannulated screw short thread/16mm; (3ea) cannulated screw short thread/17mm; (3ea) cannulated screw short thread/18mm; (3ea) cannulated screw short thread/19mm; (3ea) cannulated screw short thread/20mm; (3ea) cannulated screw short thread/21mm; (3ea) cannulated screw short thread/22mm; (3ea) cannulated screw short thread/23mm; (3ea) cannulated screw short thread/24mm; (3ea) cannulated screw short thread/25mm; (3ea) cannulated screw short thread/26mm; (3ea) cannulated screw short thread/27mm; (3ea) cannulated screw short thread/28mm; (3ea) cannulated screw short thread/29mm; (3ea) cannulated screw short thread/30mm; (3ea) cannulated screw short thread/32mm; (3ea) cannulated screw short thread/34mm; (3ea) cannulated screw short thread/36mm; (3ea) cannulated screw short thread/38mm; (3ea) cannulated screw short thread/40mm; (2ea) cannulated screw long thread/14mm; (2ea) cannulated screw long thread/15mm; (2ea) cannulated screw long thread/16mm; (2ea) cannulated screw long thread/17mm; (2ea) cannulated screw long thread/18mm; (2ea) cannulated screw long thread/19mm; (2ea) cannulated screw long thread/20mm; (2ea) cannulated screwlong thread/21mm; (2ea) cannulated screw long thread/22mm; (2ea) cannulated screw long thread/23mm; (2ea) cannulated screw long thread/24mm; (2ea) cannulated screw long thread/25mm; (2ea) cannulated screw long thread/26mm; (2ea) cannulated screw long thread/27mm; (2ea) cannulated screw long thread/28mm; (2ea) cannulated screw long thread/29mm; (2ea) cannulated screw long thread/30mm; (2ea) cannulated screw long thread/32mm; (2ea) cannulated screw long thread/34mm; (2ea) cannulated screw long thread/36mm; (2ea) cannulated screw long thread/38mm; (2ea) cannulated screw long thread/40mm; (5ea) threaded washer for 3.0mm cannulated screws; (6ea) washer 6.5mm; (10) 1.1mm threaded guide wire 150mm; (10) 1.1mm non-threaded guide wire 150mm; (1ea) 3.0mm cannulated screw instr & implant set graphic case; (1ea) conical extraction device for threaded washers; (2ea) 2.0mm cannulated drill bit/qc 150mm; (1ea) cannulated countersink for 3.0mm cannulated screws; (1ea) handle with quick coupling, small; (1ea) 2.0mm/1.1mmdouble drill sleeve; (1ea) 5.5mm/4.3mm double drill sleeve; (1ea) holding sleeve; (1ea) cannulated cruciform screwdriver; (1ea) cannulated driver for threaded washers; (1ea) 1.25mm cleaning brush; (1ea) 1.1mm cleaning stylet; (1ea) cannulated screw measuring device for 3.0mm; (1ea) screw forceps; (1ea) freer elevator 19.5cm; (1ea) scaphoid elevator 14 cm C) Small Fragment Instrument and Implant set: (6ea) 4.0mm cancellous bone screw partially threaded/30mm; (6ea) 4.0mm cancellous bone screw partially threaded/35mm; (6ea) 4.0mm cancellous bone screw partially threaded/40mm; (6ea) 4.0mm cancellous bone screw partially threaded/45mm; (6ea) 4.0mm cancellous bone screw partially threaded/50mm; (6ea) washer 7.0mm; (2ea) 3.5mm lc-dcp plate 6 holes/77mm; (2ea) 3.5mm lc-dcp plate 7 holes/90mm; (2ea) 3.5mm lc-dcp plate 8 holes/103mm; (1ea) 3.5mm lc-dcp plate 9 holes/116mm; (1ea) 3.5mm lc-dcp plate 10 holes/129mm; (1ea) small T-plate 3 holes head/3 holes shaft/50mm-right; (1ea) small T-plate 3 holes head/5 holes shaft/67mm-right; (1ea) small T-plate 3 holes head/3 holes shaft/53mm-oblique; (1ea) small T-plate 3 holes head/4 holes shaft/63mm-oblique; (1ea) small T-plate 3 holes head/5 holes shaft/75mm-oblique; (1ea) one-third tubular plate with collar 2 holes/25mm; (1ea) one-third tubular plate with collar 3 holes/37mm; (1ea) one-third tubular plate with collar 4 holes/49mm; (2ea) one-third tubular plate with collar 5 holes/61mm; (2ea) one-third tubular plate with collar 6 holes/73mm; (2ea) one-third tubular plate with collar 7 holes/85mm; (1ea) one-third tubular plate with collar 8 holes/97mm; (1ea) one-third tubular plate with collar 10 holes/121mm; (1ea) cloverleaf plate thin blade 3 holes/88mm; (1ea) cloverleaf plate thin blade 4 holes/104mm; (1tp) 1.25mm Kirschner wire w/trocar point 150mm; (1tp) 1.6mm Kirschner wire w/trocar point 150mm; (1tp)2.0mm Kirschner wire w/trocar point 150mm; (1ea) small fragment instr/implant set -- LC-DCP graphic case; (3ea) 2.5mm drill bit/qc/gold/110mm; (2ea) 3.5mm drill bit/qc/110mm; (1ea) countersink F/3 5mm cortex & 4.0mm cancellous bone screws; (2ea) tap for 3.5mm cortex screws gold/110mm; (2ea) tap for 4.0mm cancellous bone screws/110mm; (1ea) T-handle with quick coupling; (1ea) 2.0mm parallel drill guide and drill sleeve; (1ea) 3.5mm/2.5mm double drill sleeve; (1ea) 3.5mm/2.5mm insert drill sleeve; (1ea) small hexagonal screwdriver with holding sleeve; (1ea) small hexagonal screwdriver shaft; (1ea) depth gauge for 2.7mm & small screws: (1ea) sharp hook; (1ea) screw forceps; (1ea) 3.5mm LC-DCP drill guide neutral & load; (1ea) 3.5mm universal drill guide; (1ea) bending iron for 2.7mm & 3.5mm plates; (1ea) bending iron for 2.7mm & 3.5mm plates; (1ea) bending template 7 holes for 3.5mm LC-DCP plates; (1ea) bending template 9 holes for 3.5mm LC-DCP & DCP plates; (1ea) wire bending pliers 155mm; (1ea) bending iron for 1.25mm, 1.6mm & 2.0mm Kirschner wires; (1ea) reduction forceps with points narrow-ratchet 132mm; reduction forceps with points broad-ratchet 140mm; self-centering bone forceps 10mm serrated jaw speed lock; (2ea) small Hohmann retractor 8mm short narrow tip 160mm; (1ea) periosteal elevator 6mm curved blade round edge; (8ea) 3.5mm cortex screw 10mm; (8ea) 3.5mm cortex screw 12mm; (8ea) 3.5mm cortex screw 14mm; (8ea) 3.5mm cortex screw 16mm; (8ea) 3.5mm cortex screw 18mm; (8ea) 3.5mm cortex screw 20mm; (8ea) 3.5mm cortex screw 22mm; (8ea) 3.5mm cortex screw 24mm; (8ea) 3.5mm cortex screw 26mm; (8ea) 3.5mm cortex screw 28mm; (8ea) 3.5mm cortex screw 30mm; (8ea) 3.5mm cortex screw 32mm; (6ea) 3.5mm cortex screw 34mm; (6ea) 3.5mm cortex screw 36mm; (6ea) 3.5mm cortex screw 38mm; (6ea) 3.5mm cortex screw 40mm; (6ea) 3.5mm cortex screw 45mm; (6ea) 3.5mm cortex screw 50mm; (2ea) 3.5mm shaft screw 16mm; (2ea) 3.5mm shaft screw 18mm; (2ea) 3.5mm shaft screw 20mm; (2ea) 3.5mm shaft screw 22mm; (2ea) 3.5mm shaft screw 24mm; (2ea) 3.5mm shaft screw 26mm; (2ea) 3.5mm shaft screw 28mm; (2ea) 3.5mm shaft screw 30mm; (2ea) 3.5mm shaft screw 32mm; (2ea) 3.5mm shaft screw 34mm; (2ea) 3.5mm shaft screw 36mm; (2ea) 3.5mm shaft screw 38mm; (6ea) 4.0mm cancellous bone screw fully threaded/10mm; (6ea) 4.0mm cancellous bone screw fully threaded/12mm; (6ea) 4.0mm cancellous bone screw fully threaded/14mm; (6ea) 4.0mm cancellous bone screw fully threaded/16mm; (6ea) 4.0mm cancellous bone screw fully threaded/18mm; (6ea) 4.0mm cancellous bone screw fully threaded/20mm; (6ea) 4.0mm cancellous bone screw fully threaded/22mm; (6ea) 4.0mm cancellous bone screw fully threaded/24mm; (6ea) 4.0mm cancellous bone screw fully threaded/26mm; (6ea) 4.0mm cancellous bone screw fully threaded/28mm; (6ea) 4.0mm cancellous bone screw fully threaded/30mm; (6ea) 4.0mm cancellous bone screw fully threaded/35mm; (6ea) 4.0mm cancellous bone screw fully threaded/40mm; (6ea) 4.0mm cancellous bone screw fully threaded/45mm; (6ea) 4.0mm cancellous bone screw fully threaded/50mm; (4ea) 4.0mm cancellous bone screw fully threaded/55mm; (4ea) 4.0mm cancellous bone screw fully threaded/60mm; (6ea) 4.0mm cancellous bone screw partially threaded/10mm; (6ea) 4.0mm cancellous bone screw partially threaded/12mm; (6ea) 4.0mm cancellous bone screw partially threaded/14mm; (6ea) 4.0mm cancellous bone screw partially threaded/16mm; (6ea) 4.0mm cancellous bone screw partially threaded/18mm; (6ea) 4.0mm cancellous bone screw partially threaded/20mm; (6ea) 4.0mm cancellous bone screw partially threaded/22mm; (6ea) 4.0mm cancellous bone screw partially threaded/24mm; (6ea) 4.0mm cancellous bone screw partially threaded/26mm; (6ea) 4.0mm cancellous bone screw partially threaded/28mm; (2ea) Hohmann retractor 15mm 160mm; (1ea) reduction forceps with serrated jaw ratchet 144mm The entire system and its characteristics enable each part and instrument to work together and allow full functionality once appropriate items have been attached to patient. The following are the salient characteristics: 1) Maxillofacial Fixation System: (a) Screws: must consist of the following minimum characteristics: self tapping, fluted screw, in threediameters; 1.0mm, 1.3mm, and 1.5mm x 1mm increasing lengths; 1.7mm emergency screws with fluted tip, in 1mm increasing lengths; commercial pure titanium for maximum biocompatibility, corrosion resistance and MRI/CT compatibility; minimal flap depression for improved cosmetic results and increased protection of the underlying structures; provide stable fixation of the cranium (b) Plates: low profile plates designed specifically for cranial applications; 2-hole straight, 4-hole straight, adaption, square box, rectangular box, and X-plates; low profile 1.5mm plates: 2-hole straight, 4-hole straight, adaption, square box, X and Y plates; commercially pure titanium for maximum biocompatibility, corrosion resistance, and MRI/CT compatibility; minimal flap depression for improved cosmetic results and increased protection of the underlying structures; provide stable fixation of the cranium; must have a variety of mesh plates and screens available; compatible with 1.0mm and 1.3mm screws; optimum hole spacing allowing multiple screw placement options; bur hole covers; 1.3mm large and small overall diameter (c) Modules: each module must contain the necessary screwdriver handles, blades, screws, plates, and drill bits; each module must be stackable and fit inside a graphite case housing all four trays with instruments (d) Hand Instruments: combination bending pliers for 1.0mm/2.0mm plates; handle with mini quick coupling, small x2 each; plate holding forceps for 1.5mm, 2.0mm, and 2.4mm plates; combination bending/cutting pliers for 1.0mm/2.0mm plates; plate cutter for 1.0mm, 1.3mmj, 1.5mm, and 2.0mm plates; plate holding forceps, locking for 1.5mm and 2.0mm plates. 2) 3.0mm Cannulated Screw Set: (a) Screws: 2 types, stainless steel alloy 316L; short thread; 3.0mm dia, short thread, 14mm-30mm long, 1mm increments;3.0mm dia,short thread, 32mm-40mm long, 2mm increments; long thread; 3.0mm dia, long thread, 14mm-30mm long, 1mm increments; 3.0mm dia, long thread, 32mm-40mm long, 2mm increments; must be cannulated; made from stainless steel alloy 316L (b) Washers: 2 types, stainless steel alloy 316L; threaded, 5.5mm dia, 3.0mm height; smooth, 6.5mm dia (c) Guidewires: 2 types and sizes; threaded, 1.1mm dia, sharp point, 150mm long; non-threaded, 1.1mm dia, non-pointed, used for redirection of previously misplaced guidewire, 150mm long (d) Hand Instruments: drill sleeves, 2 types; 2.0mm/1.1mm double drill sleeve; 5.5mm/4.3mm double drill sleeve; quick coupling handle; cannulated countersink, quick connect with quick coupling; Posted 02/26/99 (W-SN302729). (0057)

Loren Data Corp. http://www.ld.com (SYN# 0303 19990303\65-0004.SOL)