DIRECTORATE OF CONTRACTING, BLDG 6 (MELOY HALL), ATZB-KT, FT BENNING, GA 31905-5000

32 -- CONCRETE CRUSHER/RECYLING PLANT SOL DABT10-99-Q-0121 DUE 083099 POC Purchasing Agent JUDY HODDER (706) 545-7522 CONTRACTING OFFICER VERA COOPER (706)545-2260 email-HodderJ@benning-emh2.army.mil (Site Code DABT10) E-MAIL: HodderJ@benning-emh2.army.mil, HodderJ@benning-emh2.army.mil. PORTABLE TRAILER, MOUNTED, IMPACT, OPEN CIRCUIT, CONCRETE CRUSHER/RECYCLING PLANT WITH OPTIONS & SHIPPING, PER ATTACHED DESCRIPTION AND SPECIFICATION DATA. [DESC]DESC: This is a combined synopsis/solicitation for commercial items prepared in accordance with the format in Subpart 12.6, as supplemented with additional information included in notice. This announcement constitutes the only solicitation; proposals are being requested and a written solicitation will not be issued. Solicitation No. DABT10-99-Q-0121 is issued as a Request for Quotes (RFQ). The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition circular 90-32. Solicitation is unrestricted, SIC Code 3531 and size standard 750. Line Item: 0001; Quantity: 1, Unit: Ea. Portable Trailer Mounted, Impact Open Circuit, Concrete Crusher/Recycling Plant. CAPABILITIES: Minimum design rated capacity range of 100 to 150 tons per hour, depending on specific products being made and conditions. must be capable of accepting and processing material with a minimum compression strengths of 10,000 psi, rock/sand/gravel as large as 16 inches in diameter, and capable of processing materials consisting of the following or a combination of the following: rock, sand, gravel, dolomite linestone, traprock, concrete, and C & D rubble containing rebar, concrete block, brick, and asphalt.Base Unit Consisting of: Receiving Hopper with a top opening minimum 6' x 16'. Constructed of heavy- duty steel with steel reinforcement of side plates. Vibrating Grizzly type feeder minimum 32" x 16'; include 60" tapered step grizzly of nominal 1.5" openings; belt driven and powered by variable speed minimum rated 20HP, 1200 RPM, TEFC electric motor drive, mounted as integral part with hopper on common base. Horizontal Shaft Impactor with 05 Primary/Secondary, maximum weight 20,000lbs; Minimum 33" x 32" feed opening. Fixed bar solid steel sculptured rotor with cast primary curtain, fabricated secondary curtains with wear resistant replaceable liners, hydraulic shim adjustment on secondary curtain. Crusher housing split with gas powered hydraulic opening for access to rotor, curtains and replaceable liners. Equipped with Fines Bypass Chute for diverting material to the Undercrusher gathering hopper. Under-Crusher Gathering Hopper constructed of heavy- duty steel plate with full-length rubber flashing and replaceable liners. Discharge Conveyor minimum 30" x 30' long for conveying the crusher discharge material to the front of the plant. Equipped with 20-degree troughing idlers. Shall have high impact urethane/rubber slider bed under Impactor discharge area, return rollers, lagged head pulley, wing tail pulley,telescoping belt take-ups, powered by minimum IO HP electric motor drive. Operator and Service Platforms, ladders and railings will be designed as structural steel frame with expanded metal non-skid floors. Platforms and railings shall be located at the crusher, power plant, and hopper to facilitate operation, maintenance and service. Ladders will be appropriately located to allow access to all platforms. Main Trailer Frame shall be designed and manufactured with minimum 18" wide flange beam side rails; have tri-axle suspension with 71" track axles with twelve (12) 11:00 x 22.5 12-ply tires. Brakes will be air controlled with emergency and service glad-hands. Shall be equipped with fifth wheel plate and kingpin that will hook up to commercial fifth wheel heights of 48 to 52 inches; prewired running lights with step, directional and 3 light marker bar; designed with Hydraulic Lift/Leveling consisting of a set of four stiff-leg type hydraulic cylinders controlled by gasoline-powered hydraulic unit complete with in-line load controls on each cylinder and directional control valves. Drives Guards will be constructed of formed sheet metal with wire mash, complete with hinge type doors for easy access to pulleys and belts. Central Control Panel will be NEMA 4 type box, plant mounted complete with circuit breaker, transformer, motorstarters, and fuses, emergency stop, push button two extra 15 HP starters and fuses with quick disconnect plugs for radial stackers; at least one dual 110-volt plug for electrically powered attachments. Equipped iwth remote operator's pendant complete with all start/stop and emergency stop pushbuttons. Power unit shall be plant mounted and consist of a water cooled diesel rated at a minimum 215 HP @ 1800 RPM with electronic controlled governor clutch, emergency shutdown system for low oil pressure, overspeed and high temperature. The power unit shall directly drive simultaneously both the crusher and a 100 KW generator. One 125 gallon fuel tank and two 8D batteries. Generator shall be a heavy- duty base mounted 100 KW generator capable of producing 460 volts, 3 phase electrical power; sufficient to operate all plant mounted electrical motors as well as two additional 15 HP radial stacker motors. Contain standard manufacturer's dust suppression system which will include as a minimum, a spray bar with brass nozzles and a shut off valve between the feed hopper and crusher. ADDITIONAL FEATURES, SERVICES, OPTIONS & ACCESSORIES: Magnetic Separator with a continuous belt magnet with stainless steel clad discharge belt; minimum 5 HP 1800 RPM TEFC electric motor drive. must be configured so that a magnet rectifier converts AC voltage to DC Voltage. Cross Conveyor minimum 18" x 8'6" Long with 24" deep truss frame; equipped with manual swivel wheels and 10:00 x 20, 12-ply tires on a rigid axle; manual rising and lowering mechanism, gathering hopper, pintle hook; minimum 15 HP, 1800 RPM TEFC electric motor drive prewired with 100" of cable from tail. 1-Extra set of type 222 Blow Bars and 440 Blow Bars. 2- Copies of parts, maintenance, and operators manuals; electrical hydraulic, and structural diagrams and schematics. Complete operational set-up including two days of operator/safety training to include necessary training and instructional materials. Primed and painted standard factory color. Minimum one year warranty on all parts and labor. The unit shall carry the manufacturers service and warranty policy. If all or any part of this equipment should prove defective in workmanship or materials, the manufacturer shall bear responsibility for labor, travel and cost to replace or repair the part of defect according to the manufacturer's warranty and this statement without cost to the Government. Date of delivery is 30 Oct 99, Delivered to ENVIRONMENTAL PROGRAMS BRANCH (RECYCLING), BLDG 4000, OLD CUSETTA RD., FORT BENNING, GA 31905. The provision at FAR 52.212-1, instructions to Offerors- Commercial Item, applies to this acquisition. Submit signed and dated offers to the office specified in this solicitation. Offers may be submitted on letterhead stationary. As a minimum offers must show: Solicitation Number; time specified in solicitation for receipt of offers; Name, Address, Telephone number of offer; a technical description of item being offered in sufficient detail to evaluate compliance with requirement n the solicitation; Price, and any discount terms; Remit to address if different than mailing address; a completed copy of the representation and certifications at FAR 52-212-3; acknowledgement of solicitation (if any). Include a statement specifying the extent of agreement with all terms, conditions, and provisions included in the solicitation. Offers that fail to furnish required representations may be excluded from consideration. Offeror agrees to hold the price in its offer firm for a period of 30 calendar days from the date specified for receipt of offers, unless another time period is specified in an addendum to the solicitation. The Government will award a PURCHASE ORDER from this solicitation to the offeror whose offer conforming to the solicitation meets the exact specifications or exceeds the specifications in the solicitation and will be the most advantageous to the Government, price and other factors considered. The clause at FAR 52.212.4, Contract Terms and Conditions-Commercial Items, applies to this acquisition. Changes in the terms and conditions of this PURCHASE ORDER may be made only by written agreement of the parties. This PURCHASE ORDER is subject to DFARS Clause 252.0204-7004, Required Central Contractor (Mar 1998), and DFARS Clause 252.232-7009, Payment by Electronic Funds Transfer (CCR) (Jun 1998) (Reference 32.1103). The clause at FAR 52.212-5, Contract Terms and Conditions Requiared to Implement Statutes or Executive Orders-Commercial Items, applies and incorporated into this PURCHASE ORDER. RESPONSES DUE 30 AUG 99, 1400 HRS local time. Request responses be faxed to JUDY HODDER, FAX NO: 706- 545-6528. NO PHONE CALLS PLEASE! Posted 08/21/99 (A-SN370794). (0233)

Loren Data Corp. http://www.ld.com (SYN# 0041 19990825\32-0001.SOL)