Fleet & Industrial Supply Center, Regional Contracts Dept, Attn: Bid Officer/Code 210A94, 937 N. Harbor Drive, Suite 212, San Diego, CA 92132-0212

34 -- HONING MACHINE SOL N00244-00-T-0474 DUE 022200 POC Nicole Hunga, Contract Specialist Phone: (619) 532-2574 Fax: (619) 532-1088 WEB: Click here to view additional business opportunities, http://www.neco.navy.mil. E-MAIL: Click here to contact the Contract Specialist via, nicole_m_hunga@sd.fisc.navy.mil. This is a combined synopsis-/-solicitation for a commercial item prepared in accordance with the Federal Acquisition Regulation (FAR) Part 12.6 as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; proposals are being requested and THERE WILL BE NO WRITTEN REQUEST FOR QUOTATION ISSUED. The solicitation number for this Request for Quotation is N00244-00-T-0474. This solicitation and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 97-14. This solicitation is issued on a restricted basis as a total small business set aside under Standard Industrial Code (SIC) 3541, Machine Tools, Metal Cutting Types with a size standard of 500 employees. FISC San Diego has a requirement for the following Contract Line Items (CLINs): CLIN 0001 is for a Honing Machine, Sunnen Products Company Part No. HL1502E or Equal, Quantity of One (1). Horizontal Tube Type. Characteristics Of The Hone Are To Be As Follows: Bore ID Honing Capability: 990" To 19", Bore Length Honing Capability: 4" To 60", Maximum Work Piece OD: 20", Spindle Speed In RPM's 67 To 336 (Variable), Spindle Stroke Rate: Up To 1000 ipm, Spindle Drive: 4hp., Machine Control: PLC, Tool Feed System: Automatic (Load Compensated), Stroke Drive System: Hydraulic Cylinder. Machine Weight Should Not Exceed 3100 Lbs, And Physical Size Should Not Exceed 227" X 52" X 65". Machine Should Also Include Automatic Cycle Timer, Build-In Spindle Load Meter To Monitor Honing Process, And A Short Stroke And Dwell For Blind Bore And Tight Spot Applications. Honing Machine To Include All Fluids Required For Normal Operation. Honing Machine To Include Tool Storage Cabinet. Honing Machine To Come Fully Equipped With All Tools, Adapters, And Stones To Hone ID Holes From 1.98" To 7". CLIN 0001 is to include the following equipment: hone head module part no. MPSH50 -- qty 1 each, hone head module part no. MPSH70 -- qty 1 each, hone head module part no. MPSH85 -- qty 1 each, adapter set part no. MPS2200 -- qty 2 each, adapter set part no. MPS2201 -- qty 1 each, master holder set 1.98-2.4 part no. MPSM1050 -- qty 2 each, master holder set 2.35-3.0 part no. MPSM1060 -- qty 2 each, master holder set 2.9-3.5 part no. MPSM2073 -- qty 2 each, master holder set 3.4-4.4 part no. MPSM2085 -- qty 2 each, master holder set 3.4-4.4 part no. MPSM3085 -- qty 2 each, master holder set 4.0-5.5 part no. MPSM3100 -- qty 2, master holder set 5.0-7.0 part no. MPSM 3125 -- qty 2 each, drive and feed ext (100mm) part no. MPSE2100 -- qty 3 each, drive and feed est (150mm) part no. MPSE2015 -- qty 1 each, disassembly rings part no. MPSER22 -- qty 3 each, stone set part no. H50A45 -- qty 25 each, stone set part no. H50J66 -- qty 25 each, stone set part no. H50A67 -- qty 10 each, stone set part no. H70A45 -- qty 25 each, stone set part no. H70J65 -- qty 25 each, stone set part no. H70A67 -- qty 10 each, MB stone set (replaced by H7) part no H70DM85XG71 -- qty 1 each, MB stone set (replaced by H5) part no H50DM85XG71 -- qty 1 each, porta hone part no R3GP281500WD -- qty 1 each, and filter element part no. PF1104 -- qty 3 each. Equipment to include training for operators and maintenance personnel to allow full operation and preventive and corrective maintenance. Three (3) sets of manuals must be included. Delivery is required not later than 15 May 2000. Delivery is F.o.b. Destination. Delivery shall be made to: Naval Aviation Depot North Island, San Diego, CA 92135-7058. Acceptance shall be at destination. The following provisions apply FAR 52.212-1, Instructions to Offerors Commercial Items, Addendum to FAR 52.000-1, Paragraph (b) (5) Offers shall provide an EXPRESS WARRANTY which at a minimum shall be the same warranty terms, including offers of extended warranties, offered to the general public. Express warranties shall be included in the contract. FAR 52.212-4 Contract Terms and Conditions Commercial Items, applies as do the following addendum clauses; FAR 52.247-34, F.o.b. Destination. The clause at 52.212-5 Contract Terms and Conditions Required To Implement Statues or Executive Orders Commercial Item applies with the following applicable clauses for paragraph (b): FAR 52.222-21 Prohibition of Segregated Facilities, FAR 52.222-26 Equal Opportunity; FAR 52.222-35 Affirmative Action for Special Disabled and Vietnam Era Veterans, FAR 52.222-36 Affirmative Action for Handicapped Workers, FAR 52.222-37 Employment Reports on Special Disabled Veterans and Veterans of the Vietnam Era, FAR 52.232-33 Payment by Electronic Funds Transfer-Central Contractor Registration, FAR 52.211-6 Brand Name or Equal, DFAR 252.204-7004 Required Central Contractor Registration, applies to all solicitations issued on or after 6/1/98. LACK OF REGISTRATION IN THE CCR DATABASE WILL MAKE AN OFFEROR/QUOTER INELIGIBLE FOR AWARD. Please ensure compliance with this regulation when submitting your quote. For more information call 1-888-227-2423 or visit the internet web site http://www.ccr2000.com . DFAR 252.212-7001 Contract Terms and Conditions Required to Implement Statutes or Executive Orders Applicable to Defense Acquisition of Commercial Items, applies with the following clauses applicable for paragraph (b) DFAR 252.225-7001 Buy American Act and Balance of Payment Program. The Government intends to make a single award to the responsible Offeror whose offer is the most advantageous to the Government considering price and price related factors. Provision 52.212-2 Evaluation Commercial Items applies with paragraph (a) completed as follows: Award will be made to the Offeror that meets the solicitation's minimum criteria for technical acceptability at the lowest price. TO BE DETERMINED TECHNICALLY ACCEPTABLE the Offeror must furnish product literature that demonstrates the products offered meet all requirements stated in the above purchase description for Line Items 0001. OFFERORS ARE REQUIRED TO COMPLETE AND INCLUDE A COPY OF THE FOLLOWING PROVISIONS WITH THEIR PROPOSALS: FAR 52.212-3, Offeror Representation and Certifications Commercial Items. ALL RESPONSIBLE OFFERORS ARE TO SUBMIT CURRENT PRICING, DELIVERY TIME, COMMERCIAL WARRANTY INFORMATION, PAYMENT TERMS, CAGE CODE, DUNN AND BRADSTREET NUMBER, TAX IDENTIFICATION NUMBER AND ALL APPLICABLE SPECIFICATIONS REGARDING THIS SOLICITATION. ALSO REQUIRED ARE COPIES OF APPLICABLE COMMERCIALLY PUBLISHED PRICE LISTS PERTAINING TO YOUR COMPANY'S PRODUCTS THAT MEET THE SPECIFICATIONS. QUOTES MUST BE RECEIVED NO LATER THAN 3:00 p.m. PST, February 22, 2000 and will be accepted via FAX (619-532-1088) Attn: Nicole Hunga. DO NOT MAIL. Note: IMPORTANT INTERNET ADDRESSES: 1) Federal Acquisition Regulations (FAR) at http://www.arnet.gov/far; 2) Defense Federal Acquisition Regulation Supplement (DFARS) at http://www.acq.osd.mil/dp/dars/dfars.html; and 3) Other federal/defense links (e.g. Central Contractor Registration On-line, Commerce Business Daily On-Line) can be accessed on the Internet at http://www.acq.osd.mil/dp (scroll down to the bottom of the page for numerous links). Posted 02/07/00 (W-SN422590). (0038)

Loren Data Corp. http://www.ld.com (SYN# 0186 20000209\34-0001.SOL)