General Services Administration, Federal Supply Service (FSS), Hardware and Appliance Center (6FE), 1500 East Bannister Road, Kansas City, MO, 64131

51 -- C-CLAMP, STOCK SOL 5120-C-CLAMP DUE 032200 POC Wayne Goin, Contract Specialist, Phone (816) 823-1280, Fax (816) 926-3678, Email wayne.goin@gsa.gov -- Arlene Tittle, Contract Specialist, Phone (816) 926-7588, Fax (816) 926-3678, Email arlene.tittle@gsa.gov WEB: Visit this URL for the latest information about this, http://www.eps.gov/cgi-bin/WebObjects/EPS?ACode=P&ProjID=5120-C-CLAMP&; LocID=7. E-MAIL: Wayne Goin, wayne.goin@gsa.gov. THIS IS A STOCK ITEM. BAR CODING REQUIRED. SOURCE INSPECTION. FOB DESTINATION. 5120-00-222-1612 UI: EA CLAMP, C: DESCRIPTION In accordance with COMMERCIAL ITEM DESCRIPTION A-A-431D, Dated 8 JAN 88. NSN: 5120-00-222-1612 EXCEPTION(S) TO TECHNICAL DOCUMENT: Page 2, column titled "B Working depth (min.)", delete "2-1/4" and substitute "2". EXCEPTION(S) TO TECHNICAL DOCUMENT Under "QUALITY ASSURANCE PROVISIONS", add the following: "Responsibility for inspection. Unless otherwise specified in the contract, the contractor is responsible for performance of all inspection requirements as specified herein. Except as otherwise specified in the contract, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the government. The government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements." Delete paragraphs titled "Examination of the end item for defects in dimensions, finish, markings and workmanship" and "Sampling for tests" and substitute: "Sampling for examination and inspection. Three random samples shall be selected for examination and inspection to determine compliance with the requirements. If any of the samples are found to be defective, the entire lot shall be rejected." Delete "Tensile test" and "Hardness test". QUALITY ASSURANCE: Delete references to "MIL-STD-105" and substitute "ANSI/ASQ-Z1.4 1993". WORKMANSHIP Details of workmanship shall be in accordance with the best commercial standards and practices. Paints, coatings, platings, and finishes shall be smooth, dry, adherent, continuous, and not stained or discolored. Fasteners shall be firmly secured and show no evidence of deformation, cross threading, or hazardous burrs. Adhesives and lubricants adequate for their intended purpose shall be properly and neatly applied. Adhesives shall be adequately cured. Wiresand cables shall be neatly dressed and shall not be frayed or in contact with sharp edges. Wire and cable insulation shall show no evidence of burns, abrading, or pinch marks. There shall be no interference, binding, or galling of parts. External and bearing surfaces shall be free of tool and gouge marks, nicks, or other surface imperfections. The item shall be clean and free of corrosion and debris (e.g., chips, shavings, slivers) or other foreign material. The item shall be free from manufacturing workmanship defects (e.g., loose, missing, binding or misaligned parts, sharp or rough external edges, corners or surfaces) and material workmanship defects (e.g., pits, rips, fins, burrs, tears, nodules, cracks, blisters) which may adversely impact the item's serviceability, durability, safety, or appearance. ITEM MARKING Each item (including all items within a set or kit) shall be marked with the manufacturer's name and identifying symbol, and the state or country of manufacture, unless otherwise specified. Allmarking shall be engraved, etched, molded, or indented. PACKAGING One (1) item shall be preserved and packaged in a unit package designed to protect the item against damage during shipment, handling, and storage. PACKING The unit packages shall be packed in a close fitting fiberboard box, grade 200 minimum. The complete pack shall be in compliance with the Uniform Freight Classification and the National Motor Freight Classification. MARKING All unit, intermediate, exterior shipping containers, and palletized or unitized loads shall be marked for delivery to civilian activities in accordance with latest version of FED-STD-123 or for delivery to military activities in accordance with latest version of MIL-STD-129, as applicable. Posted 03/17/00 (D-SN435553). (0077)

Loren Data Corp. http://www.ld.com (SYN# 0192 20000321\51-0003.SOL)