General Services Administration, Federal Supply Service (FSS), Hardware and Appliance Center (6FE), 1500 East Bannister Road, Kansas City, MO, 64131

51 -- 5120-HAMMER-HAND SOL 5120-E4-HAMMER-HAND DUE 033100 POC Wayne Goin, Contract Specialist, Phone (816) 823-1280, Fax (816) 926-3678, Email wayne.goin@gsa.gov -- Arlene Tittle, Contract Specialist, Phone (816) 926-7588, Fax (816) 926-3678, Email arlene.tittle@gsa.gov WEB: Visit this URL for the latest information about this, http://www.eps.gov/cgi-bin/WebObjects/EPS?ACode=R&ProjID=5120-E4-HAMME R-HAND&LocID=7. E-MAIL: Wayne Goin, wayne.goin@gsa.gov. STOCK PROGRAM, BAR CODING REQUIRED, SOURCE INSPECTION, FOB DESTINATION (DESIRED), QUANTITY NEEDED: 1,326. 5120-00-061-8546 UI: EA HAMMER, HAND: DESCRIPTION In accordance with Commercial Item Description A-A-1305B, dated 04/17/89. Machinists' Ball Peen Hammer Head Weight: 32 ounces, plus or minus 4 ounces. Handle Material: Fiberglass. Overall length: 16.0 inches. EXCEPTION(S) TO TECHNICAL DOCUMENT Delete "Finish" paragraph and substitute the following: "Finish. The striking face shall have a roughness value less than 125 microinches when calculated as an arithmetic average. Other areas shall have a surface finish conforming to good commercial practice. Hammers shall be tested for surface finish roughness in accordance with ANSI/ASME B46.1 prior to lacquering or coating." Delete "Handle" paragraph and substitute the following: "Handle. The handle shall be made of hickory wood or fiberglass with a handgrip as specified. When hickory is required, the handle shall be Grade A hickory wood in accordance with Federal Specification NN-H-93C; except in Table I of NN-H-93C, column titled 'Maximum admissible blemishes and defects', delete all text except for 'Four medium streaks or equivalent in shorter streaks. Light stain.' Table, Head Weight tolerance, add a negative tolerance equal to the plus tolerance shown in the chart. Table, Overall Length tolerance, delete "plus 1 inch" and substitute "plus or minus 1 inch". Table, delete eye dimension tolerances and substitute "Plus 1/8 inch minus 1/16 inch". Page 4, under "Notes", add the following: "An acceptable alternative to the Rockwell C hardness is the equivalent Brinell hardness as specified in ASTM E140-86 when tested with a 3000kg, 10mm, standard or tungsten carbide ball." WORKMANSHIP Details of workmanship shall be in accordance with the best commercial standards and practices. Paints, coatings, platings, and finishes shall be smooth, dry, adherent, continuous, and not stained or discolored. Fasteners shall be firmly secured and show no evidence of deformation, cross threading, or hazardous burrs. Adhesives and lubricants adequate for their intended purpose shall be properly and neatly applied. Adhesives shall be adequately cured. Wires and cables shall be neatly dressed and shall not be frayed or in contact with sharp edges. Wire and cable insulation shall show no evidence of burns, abrading, or pinch marks. There shall be no interference, binding, or galling of parts. External and bearing surfaces shall be free of tool and gouge marks, nicks, or other surface imperfections. The item shall be clean and free of corrosion and debris (e.g., chips, shavings, slivers) or other foreign material. The item shall be free from manufacturing workmanship defects (e.g., loose, missing, binding or misaligned parts, sharp or rough external edges, corners or surfaces) and material workmanship defects (e.g., pits, rips, fins, burrs, tears, nodules, cracks, blisters) which may adversely impact the item's serviceability, durability, safety, or appearance. ITEM MARKING Each item (including all items within a set or kit) shall be marked with the manufacturer's name and identifying symbol, and the state or country of manufacture, unless otherwise specified. All marking shall be engraved, etched, molded, or indented. PACKAGING Six (6) items shall be preserved and packaged in a unit package designed to protect the item against damage during shipment, handling, and storage. PROHIBITION OF PLASTIC PACKAGING AND PACKING Plastic in packaging, packing and associated marking materials are prohibited. The definition of plastic shall be as defined in ASTM D883-93. PACKING The unit packages shall be packed in a close fitting fiberboard box, grade 200 minimum. The complete pack shall be in compliance with the Uniform Freight Classification and the National Motor Freight Classification. MARKING All unit, intermediate, exterior shipping containers, and palletized or unitized loads shall be marked for delivery to civilian activities in accordance with latest version of FED-STD-123 or for delivery to military activities in accordance with latest version of MIL-STD-129, as applicable. Posted 03/22/00 (D-SN437006). (0082)

Loren Data Corp. http://www.ld.com (SYN# 0221 20000324\51-0001.SOL)