Loren Data Corp.

'

  
COMMERCE BUSINESS DAILY ISSUE OF JULY 12,2000 PSA#2640

Procurement Division, Naval Air Station Oceana, Supply Dept. Bldg 730, Virginia Beach, VA 23460-5120

59 -- ELECTRICAL EQUIPMENT AND COMPONENTS SOL N60191-00-Q-0004 DUE 072600 POC Tina Barnes 757-433-2361 E-MAIL: Tina Barnes, barnest@nasoceana.navy.mil. THIS IS COMBINED SYNOPSIS/SOLICITATION FOR COMMERCIAL ITEMS PREPARED IN ACCORDANCE WITH FORMAT IN SUBPARTS 12.6 AND 13.5, AS SUPPLEMENTED WITH ADDITIONAL INFORMATION INCLUDED IN THIS NOTICE. THE ANNOUNCEMENT CONSITUTES THE ONLY SOLICITATION; QUOTES ARE BEING REQUESTED AND A WRITTEN SOLICITATION WILL NOT BE ISSUED. SOLICITATION N60191-00-Q-0004 IS ISSUED AS A REQUEST FOR QUOTATIONS FOR ELECTRICAL EQUIPMENT AND PARTS AND INCORPORATES PROVISIONS AND CLAUSES IN EFFECT THROUGH FEDERAL ACQUISITION CIRCULAR 97-12. THIS ACQUISITON IS A BRAND NAME OR EQUAL REQUIREMENT. FOB DESTINATION IS REQUIRED BY THE GOVERNMENT AND DESIRED DELIVERY DATE IS 14 AUG 00. ITEM 0001 RELAY, MFR: GE P/N 12IJS52DIA, 2 EACH, SYNCHRONISM CHECK, TYPE IJS, COMPLETE WITH DRAWOUT CASE FOR 1/8" THICK PANEL, CASE SIZE S-1, DEVICE #25, TYPE ISJ52D SYNCHRONISM CHECK WITH 2-INSTANTANEOUS UNDER VOLTAGE UNITS BUSS AND LINE, 60HZ, 115 VAC, CLOSING ANGLE AT RATED VOLTS 20 DEGREES, 1-N-0 MAIN CONTACT. ITEM 0002 RELAY, MFR: GE P/N 12IBC51M1A, 4 EACH,DIRECTIONAL OVERCURRENT, TYPE IBC, USED PRIMARILY FOR PROTECTION OF FEEDERS AND TRANSMISSION LINE IN APPLICATIONS WHERE SINGLE PHASE RELAYS ARE REQUIRED. RELAYS CONSIST OF TWO UNITS, AN INSTANTANEOUS POWER-DIRECTIONAL UNIT (BOTTOM) OF THE INDUCTION-CUP TYPE AND A TIME OVERCURRENT UNIT (TOP) OF THE OVERCURRENT DISK TYPE. DIRECTIONAL UNIT CONTRACTS CONTROL OPERATION OF THE OVERCURRENT UNIT (DIRECTIONAL CONTROL) IBC PHASE TYPE, 120V, 60HZ, TIME UNIT 2-16, INVERSE TIME, 1 N.O. CONTACT, DEVICE #67, COMPLETE WITH CASE (M-1) FOR 1/8" THICK PANEL, RELAY TYPE IBC. ITEM 0003 RELAY, MFR: WESTINGHOUSE, P/N 291B318A09, 2 EACH, PILOT WIRE, HIGH SPEED, TPE HCB-1, APPLICATION 2 OR 3 TERMINAL LINES, 4-12 AMP, 60HZ, INSTANTANEOUS, 0.2/2.0 AMPS, DC (INDICATING CONTACTOR SWITCH), 1-HCB-1 SPST-CC, INTERNAL SCHEMATIC #763A227, CASE SIZE FT-42DEVICE #85, WESTINGHOUSE STYLE #292B930A29A, COMPLETE WITH INSULATING TRANSFORMER 60HZ, 4/1, PANEL THICKNESS 1/8" WESTINGHOUSE STYLE #7882A26G07. W-2 SWITCH, PANEL THICKNESS 1/8" WESTINGHOUSESTYLE 508A468G01 AND RC-351 MILLIAMMETER, FLUSH MOUNTING CASE, 1/8" PANEL THICKNESS 60HZ AC, 0-5, 0-25 MA. 0004 TRANSFORMER, MFR: ASSOCIATED ENGINEERING CO, P/N G830300DO, 6 EACH, POTENTIAL, TYPE SPOF-200, 60 H Z VOLTAGE 34.5 KV, 200BIL, RATIO 300/175:1, BURDEN 0.3 AT W.X,Y,Z, THERMAL RATING 4000 VA, DISTRIBUTION CLASS, OIL FILLED, SINGLE BUSHING, FOR L-G APPLICATIONS. SEC. VOLTAGE 115/67.08V. ITEM 0005 LAMP ASSEMBLIES, MFR: GE, P/N 116B6708G43A53A4, QTY: 2 EACH,INDICATING, LED, DESIGNED FOR APPLICATION ON CONTROL PANELS UP TO AND INCLUDING A " THICKNESS. ASSEMBLIES CONSIST OF (3) THREE COMPONENTS: (1) LAMP RECEPTACLE WITH RESISTOR (125 VDC, 110 MIN, 140 MAX), (2) THE LED LAMP (AMBER) AND (3) TRANSPARENT COLOR LENS CAP (AMBER). ITEM 0006 TERMINAL BLOCK, MFR: GE, P/N EB25812W (REPLACES #EB25A12W), QTY: 40 EACH, TYPE EB 25, ONE PIECE, MOLDED WITH WASHER HEAD BINDING SCREWS (10-32), 12 CIRCUIT WITH BLANK FIBER MARKING STRIP FOR CIRCUIT IDENTIFICATION. ITEM 0007 HOLDER FUSE, MFR: GE P/N 8431-3, QTY: 4 EACH, CARTRIDGE TYPE, 250 VOLT, BLACK PHENOLIC TRIPLE POLE, 1-30 AMP RATING WITH SCREW TERMINALS, BASE LENGTH 3" WIDE 3.125, HEIGHT 1.375". ITEM 0008 -- TEST BLOCK, MFR: GE P/N 6422120G4, QTY: 10 EACH, 6 POLE JACKS WITH TEXTOLITE COVER THAT HAVE INTERNAL PLUG CONTACTS WHICH MAKE A THROUGH CONNECTION WHEN COVER IS IN PLACE. CONTRACT RATING IS 250 VOLTS, 10 AMPS CONTINUOUSLY. COMPLETE WITH MOUNTING SCREWS, NUTS, AND BUSHINGS FOR STUDS. ALSO, A SET OF UNMOUNTED AUXILIARY CONTACTS, JUMPERS AND SCREWS IN SUFFICIENT VARIETY AND QUANTITY TO PROVIDE THE COMBINATIONS TO SUIT ANY APPLICATION DESIRED FOR SURFACE MOUNTING ON 1/8"-1/2" PANELS, TYPE PK-2. ITEM 0009 HOLDER FUSE, MFR: GE, P/N 8411-3, QTY: 4 EACH, CARTRIDGE TYPE, 250 V, BLACK PHENOLIC, SINGLE POLE, 1-30 AMP RATING, WITH SCREW TERMINALS BASE LENGTH 3" WIDTH 1.218, HEIGHT 1.375". ITEM 0010 HOLDER FUSE, MFR: GE P/N 8421-3, QTY: 2 EACH, CARTRIDGE TYPE, 250 V. BLACK PHENOLIC, DOUBLE POLE, 1-30 AMP RATING, WITH SCREW TERMINALS, BASE LENGTH 3", WIDTH 2.156, HEIGHT 1.375".ITEM 0011 BUSS SUPPORT FOR COPPER TUBE (1 "), MFR: BURNDY P/N UH16-3B, QTY: 18 EACH, HIGH COPPER ALLOY FOR MOUNTING TUBE ON A POST OR PEDESTAL TYPE INSULATOR. SINGLE BOLT ALLOWS ROTATION TO ANY ANGLE, 3" BOLT CIRCLE, BURNDY TYPE UH (INCLUDES MOUNTING HARDWARE). ITEM 0012 JUMPER, MFR: BURNDY, P/N B22G124N, QTY: 18 EACH, FLEXIBLE COPPER BRAID DESIGNED TO TAKE UP LINEAR EXPANSION AND CONTRACTION, COMPENSATE FOR MISALIGNMENT AND TO ABSORB VIRBRATORY MOVEMENT OF ELECTRICAL EQUIPMENT, MADE OF FLAT, EXTRA FLEXIBLE TINNED OR SOLVER PLATED PURE COPPER BRAID, WITH SILVER RLATED SEAMLESS, PURE COPPER FERRULES FORMED INTO A RECTANGLAR SHAPE ON EACH END, 1200 AMP CAPACITY MUST CARRY 1200 AMPS, 4 HOLE NEMA DRILLED PADS TO FIT 4 HOLE NEMA FLAT TERMINAL, (TYPE B). ITEM 0013 BUS COUPLER, MFR: BURNDY P/N NS1616, QTY: 12 EACH, STRAIGHT, FOR COPPER TUBLE TO TUBE, 1 " TO 1 ", TYPE NS, HIGH COPPER ALLOY COUPLER FOR JOINING EQUAL SIZES OF TUBE END TO END. ITEM 0014 TERMINAL FOR JOINING COPPER, MFR: BURNDY P/N NA16-4N, QTY: 36 EACH, 1 " TUBE TO FLAT PAD, MADE FROM HIGH COPPER ALLOY, PAD PRE-DRILLED TO NEMA STANDARDS (4 HOLES, 9/16"), TYPE NA. ITEM 0015 "T" CONNECTOR FOR COPPER BUSS, MFR: BURNDY, P/N NT1616, QTY: 18 EACH, TUBE TO TUBE, HIGH COPPER ALLOW T-CONNECTOR FOR TUBING RUN AND TAP. SLOTS BETWEEN BOLT PROVIDE INDEPENDENT HIGH PRESSURE AREAS OF CONTACT: 1 " X 1 " X 1 ". ITEM 0016 "T" CONNECTOR FOR COPPER BUSS, MFR: BURNDY, P/N NHNT1629, QTY: 6 EACH, TUBE TO CABLE, (1 " TUBE TO #4 AWG CABLE) HIGH COPPER ALLOW "T" CONNECTOR FOR JOINING COPPER BUSS RUN TO COPPER TAP CABLE. TAP UTILITIES REVERSIBLE CAP TO ACHIEVE LARGE CONDUCTOR RANGE. ITEM 0017 ELBOW, 90 DEGREES, MFR: BURNDY, P/N NL1616, QTY: 24 EACH, 1 1/4" X 1 " COPPER BUSS TUBE, HIGH COPPER ALLOY. ITEM 0018 TERMINAL FOR COPPER TUBE, MFR: BURNDY P/N NA16-2N, QTY: 12 EACH, (1 " DIA.) TO FLAT, TYPE NA, HIGH COPPER ALLOY FOR JOINING COPPER BUSS (1 " DIA TO EQUIPMENT PADS, 1 " TUBE TO 2 HOLE NEMA FLAT. ITEM 0019 TERMINAL FOR COPPER CABLE, MFR: BURNDY P/N NAH29-2N, QTY: 6 EACH, (#6 AWG TO 250 KCMIL) TO NEMA 2 HOLE PAD, TYPE NAH, HIGH COPPER ALLOW, REVERSIBLE CAP TERMINAL FOR JOINING CABLE TO EQUIPMENT PADS (FIG ID). ITEM 0020 -- END CAP FOR 1 " COPPER BUSS TUBING, MFR: BURNDY P/N LB16, QTY: 12 EACH. ITEM 0021 SWITCHBOARD WIRE, QTY: 6 LG,TYPE SIS #12 AWG, GRAY COLOR, TINNED, STRANDED COPPER, SEPERATOR, WV-1XLP, INSULATION, 600 VOLTS, 90 DEGREE C, STRADING 65/.0100 TC, INS., .030, O.D. 162 STANDARD PUT-UPS S500/R5000. ITEM 0022 DUCT, MFR: PANDUCT-PANDUCT, P/N E2X2LG6, QTY: 6 LENGTHS, DUCT, PLASTIC WIRING, 2" X2" OPEN SLOT, GRAY, 6 FT, LENGTHS TYPE E, TOTAL OF 36 FT REQUIRED). ITEM 0023 -- COVERS, MFR: PANDUIT-PANDUCT P/N C2LG6, QTY: 6 EACH, PLASTIC GRAY, 6 FT. LENTHS, (TOTAL OF 36 FT REQUIRED) TO FIT ABOVE PANDUIT-PANDUCT PLASTIC DUCT. ITEM 0024 CABLE SUPPORT GRIPS, MFR: WOODHEAD P/N 35007, QTY: 6 EACH; WIRE MESH, DOUBLE EYE, SINGLE WEAVE, CLOSED MESH FOR USE TO SUPPORT VERTICAL CABLE RUNS, WOODHEAD CAT #5007, PRODUCT SELECTION #SC175-UU. ITEM 0025 WIRE, COPPER, QTY: 450 FT, #4/0 AWG CLASS B STRANDED COPPER CONDUCTORS, 19 STRANDS, GROUNDING WIRE. ITEM 0026 35 KV COLD SHRINK TERMINIATION KIT FOR 750 KCMIL COPPER. MFR: 3M P/N 5698K, QTY: 4 KT, PVC JACKETED 133: INSULATION EPR CABLE (2.22" O.D.) WITH A TAPE SHIELD. EACH KIT SHALL CONTAIN MATERIAL FOR 3-35KV TERMINATIONS. THE TERMINATIONS SHALL BE MADE FROM SILICONE RUBBER WITH 8 SKIRTS. ITEM 0027 TWO-HOLE COPPER LUGS WITH A LONG BARREL TO FIT 750 KCMIL COPPER STRANDED CABLE ABOVE (35KV). MFR: 3M P/N 31172. QTY: 12 EACH. ITEM 0028 2" HIGH MOUNTING BASE. MFR; LAPP P/N AP-3-5, QTY: 18 EACH; FOR T.R. 210 STATION POST INSULATORS (34.5 KV) HAVING A 3" BOLT CIRCLE BASE, MOUNTING B ASE SHALL BE MALLEAB LE IRON HOT-DIP GALVANIZED WITH A 5" BOLT CIRCLE BASE. INCLUDES CAP SCREWS FOR 3" BOLT CIRCLE. ITEM 0029 INSULATOR, STATION POST; MFR: LAPP P/N 9785-70; QTY: 18 EACH; 38KV, MOUNTING CAPS TO HAVE FOUR UNC STANDARD " 13 TAPPED HOLES, 11/16" DEEP ON A STANDARD 3" BOLT CIRCLE, GRAY GLAZED PORCELAIN, ANSI C29.7, CLASS 57-4. ITEM 0030 BUS TUBING, COPPER; QTY: 540 FT; 1 "M SCHEDULE 40, SUITABLE FOR USE IN OUTDOOR 34.5 KV STATIONS, 20" LENGHTS, TYPE SPS. FOR TECHNICAL INFORMATION CONTACT W. FOGLE @ 757-396-5859. THE SOLICITATION INCORPORATES PROVISIONS AND CLAUSES IN ACCORDANCE WITH FEDERAL ACQUISITON CIRCULAR 97-12 AS FOLLOWS: EVALUATION 52.212-1 INSTRUCTIONS TO OFFEROR COMMERCIAL; 52.212-2 -- EVALUATIONS COMMERCIAL ITEMS; 52-212-3 OFFEROR REPRESENTATIONS AND CERTIFICATIONS COMMERCIAL ITEMS; 52.212-4, CONTRACT TERMS AND CONDITIONS COMMERICIAL ITEMS; 52.212-5 CONTRACT TERMS AND CONDITIONS REQUIRED TO IMPLEMENT STATUTES OR EXECUTIVE ORDER; 252-7004 REQUIRED CONTRACTOR REGISTRTATION APPLIES. ALL RESPONSIBLE SOURCES MAY SUBMIT AN OFFER AND WILL BE CONSIDERED. FAX PROPOSALS WILL BE RECEIVED AT 757-433-2176 ON OR BEFORE 07/26/00. Posted 07/10/00 (W-SN472949). (0192)

Loren Data Corp. http://www.ld.com (SYN# 0263 20000712\59-0009.SOL)

59 - Electrical and Electronic Equipment Components Index  |  Issue Index |


Created on July 10, 2000 by Loren Data Corp. -- info@ld.com