SOURCES SOUGHT
N -- Install a fully functional, production ready advanced coatings removal system for large and small landing gear components. The CRP needs to reduce flow time from days to hours, is entirely “green”, does not damage parts, requires only a single operator,
- Notice Date
- 1/14/2010
- Notice Type
- Sources Sought
- NAICS
- 332812
— Metal Coating, Engraving (except Jewelry and Silverware), and Allied Services to Manufacturers
- Contracting Office
- Department of the Air Force, Air Force Materiel Command, Tinker OC-ALC - (Central Contracting), 3001 Staff Drive, Ste 1AG76A, Tinker AFB, Oklahoma, 73145-3015
- ZIP Code
- 73145-3015
- Solicitation Number
- LP702
- Archive Date
- 2/13/2010
- Point of Contact
- Frederic A. Veal, Phone: 4057348737
- E-Mail Address
-
frederic.veal@tinker.af.mil
(frederic.veal@tinker.af.mil)
- Small Business Set-Aside
- N/A
- Description
- Coating Removal Process (CRP) (LP702) for Director of Propulsion Tinker AFB, OK CAUTION: This is a SOURCES SOUGHT notice. This is NOT a solicitation for proposals, proposal abstracts, or quotations. The purpose of this notice is to obtain information regarding designing, engineering, installing, demonstrating, validating, qualifying, and activating a fully functional, production ready (MRL9/TRL9) Coating Removal Process (CRP) for a green environmentally acceptable, non damaging, cost effective method of removing advanced coatings (HVOF, Plasma, SPD) from aerospace components, especially for advanced landing gear systems at MRO's. Contractors/Institutions responding to this sources sought are placed on notice that participation in this survey may not ensure participation in future solicitations or contract awards. The Government will not reimburse participants for any expenses associated with participation in this survey. The Government reserves the right to use information provided by respondents for any purpose deemed necessary and legally appropriate. Respondents are advised that the Government is under no obligation to acknowledge receipt of the information received or provide feedback to respondents with respect to any information submitted. INSTRUCTIONS: Below is a short description of the requirements, a request for your business information, and a Contractor Capability Survey which allows you to provide your company's capabilities. If, after reviewing these documents, you desire to participate in the market research, you should provide documentation that supports your company's capabilities in meeting these requirements. Failure to provide documentation may result in the Government being unable to adequately assess your capabilities. Both large and small businesses are encouraged to participate in this market research. Joint ventures or teaming arrangements are acceptable and up to each industry partner. Team members must be identified to include credentials. •4. Questions relative to this market research should be addressed to Tony Veal, 639ASCG/PK, frederic.veal@tinker.af.mil, 405.734.6724. PURPOSE/DESCRIPTION: We are conducting market research to identify potential sources that may possess the expertise, capabilities, and experience to install a fully functional, production ready advanced coatings removal system for large and small landing gear components. The CRP needs to reduce flow time from days to hours, is entirely "green", does not damage parts, requires only a single operator, is cheaper, and can be inserted directly into a lean cell NOTE: Office within 15 miles of a DoD Depot with applicable Subject Matter Expert (SME) engineering support available during installation and qualification is a must. CONTRACTOR CAPABILITY SURVEY Part I. Business Information Please provide the following business information for your company/institution and for any teaming or joint venture partners: · Company/Institute Name: · Address: · Point of Contact: · CAGE Code: •· DUNS Number: •· Phone Number: •· E-mail Address: •· Web Page URL: •· Size of business pursuant to North American Industry Classification System (NAICS) Code 332810, 332812, 333298, 333411, 333519, 333618, 336411, 336412, 336413, 541330, or 541990 (others could apply) Based on the above NAICS Code, state whether your company is: •Ø Small Business •Ø Woman Owned Small Business •Ø Small Disadvantaged Business •Ø 8(a) Certified •Ø HUBZone Certified •Ø Veteran Owned Small Business •Ø Service Disabled Small Business · Central Contractor Registration (CCR). · A statement as to whether your company is domestically or foreign owned (if foreign, please indicate the country of ownership). Part II. Capability Survey Questions Describe your past experience for designing, engineering, installing, demonstrating, validating, qualifying, and activating an advanced coating removal systemto include: •· Program name •· Government or contractor POC •· Detailed description of the device(s) •· Quantities produced •· Production schedule for both past programs and estimate for this one •· Cost of past efforts and estimate for this one •· Risks envisioned with this effort INFORMATION SUBMISSION INSTRUCTIONS: Responses must be received no later than close of business Friday, January 29, 2010. Submit responses electronically, via email, to frederic.veal@tinker.af.mil in MS Word or Adobe Portable Document Format (PDF) not to exceed 5 single sided pages presented in single-space using a 12-font size minimum. CONFIDENTIALITY: No proprietary, classified, confidential, or sensitive information should be included in the response. The Government reserves the right to use any non-proprietary technical information in any resulting solicitation(s).
- Web Link
-
FBO.gov Permalink
(https://www.fbo.gov/spg/USAF/AFMC/OCALCCC/LP702/listing.html)
- Record
- SN02042417-W 20100116/100114234445-9a3ee8cfbd61c6d5763960d46e839df0 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |